Arbor press with our conversion kit installed to allow older Lionel & other Press tools to be use. Ram has the ability to receive 3/8" & 1/2" tools. Lower plate with cups will receive 3/8", 1/2" & 5/8" tools. Tools that can be attach are the Lionel Rivet Punches & Quartering Cups.
Arbor press
- 4-3/4" Max work height (with Anvil)
- 5-3/4" Max work height (with out Anvil)
- Easily convert between Standard Arbor Press to Rivet Press
- Use 3/8" Alignment Pin or 1/2" Pointed Punch to align holes in ram & lower plate before tightening screws
- Lower plate with 5/8" hole with set screw
- 3/8" cup for Lower Plate.
- 1/2" cup for Lower Plate
- At least 3-1/2" between either the quartering cups or rivet press tools at fully open.
- 4" working depth from center of tools.
- Rivet Press & Quartering cups NOT included.
- Reversible Ram With Holes on both ends
- 3/8" hole with set screw at one end of ram
- 1/2" hole with set screw at the other end of ram
- Speed wheel with the ability to use without. Swap wheel with the Wheel Collar for more clearance.
- Adjustable Depth Stop With Fine Adjustment
- Included 1/2" press tools (are include with the base Arbor press)
Included:
- Modified Palmgren 1 ton Arbor Press
- Lower plate with 5/8" hole with set screw
- 3/8" cup for Lower Plate.
- 1/2" cup for Lower Plate
- 3/8" Alignment Pin
- Wheel Collar
- Rivet Press & Quartering cups NOT included.
- Sorry no free shipping on this tool. It weighs 36lbs.
· KW 190
· ZW 250
· ZW 275
· Z 250
· V 150
· VW 150
· We tested on these but may work on others transformers & rivets
Designed for flaring the rivets over when installing new Rivets. Can also be used to tighten up loose rivets by repressing them.
- Tool is machines from solid steel
- Small size meant you don't need to fully disassemble item.
- Larger Pocket for larger rivet head
- Designed for Aluminum & Brass Rivets
- Requires 9/64" hex wrench
- This design is a more universal with a larger Opening & Throat Depth
- Designed for older Lionel O-Gauge but should work on other brands & gauges
- Meant for Brass & Aluminum rivets
- Designed for use on 1/16", 5/32" 1/8" & Latch Coupler rivets
- The tool is machined out of :
1 - Prick Punch
1 - Holding Block
1 - Latch Coupler Rivet Support Post
1 - 1/8" Rivet Support Post
1 - 5/32" Rivet Support Post
1 - 1/16" Rivet Support Post
· Designed for drilling out rivets for removal.
· Helps by letting the top of the rivet dig into the Rivet Remover Punch so it do not spin ruin your plastic parts.
· Base Plate has mounting holes so you can screw it down.
· Rivet Remover Punch is machined out of Tool Steel & Heat Treated.
· Base Plate is machined out of solid Aluminum.
· Rivet Remover Punch is removable with a flat spot on punch & set screw in base.
· Other two holes are for holding our other Rivet .Punches sold separately.
Recommend take a punch and setting the rivet into our Rivet Remover Punch before drilling out.
Top of rivet after being removed. See marks from teeth digging in.
Includes:
1 - Base Plate
1 - Rivet Remover Punch
Shown with Rivet Punch Tools sold separately
- We redesigned the ZW-74 Switch Rivet found in VW & ZW Lionel Transformers to have a screw in the end.
- Allows for easy services & cleaning of the Whistle / Direction switch without it being unsoldered & fully removed.
- Machine from solid Brass.
Remove 2 screw hold Switch in place.
Lift Switch a little & remove screw.
Service Switch & reinstall.
Copyright © 2018 PE Design & Manufacturing - All Rights Reserved.
All tools in are the patenting process.
Powered by GoDaddy